Mac The Cable For Usb 10/100/1000 Lan Is Connected, But Your Computer Does Not Have An Ip Address.10/15/2019
Box Contents. Includes the adapter, a mini-CD containing Windows drivers, and a short page of instructions. This device is so easy to use that I found the instructions to be unnecessary. This version has a Type-A USB connector.
![]()
A version with a is also available, but I did not have one of those to try. Linux Compatibility I tried Xubuntu 14.04 and Linux Mint 18.1, and this adapter works perfectly with both. Simply plug it in, and Linux automatically recognizes it. No manual driver installation was needed.
I've tried updating the LAN drivers and intel chipset but have seen no It's always 100.00Mbps. Is it possible to get the ethernet port to 200Mbps? I've done a lot of reading over the last couple weeks on internet speeds, and it but the cable only supports 100Mbps or the Ethernet ports on the homeplugs.
The USB adpater may appear as “ASIX Elec. AX88179” in the panel notification area if you click the network icon in the panel.
Here, the USB adapter is connected to a LAN. IP Address Assignment Linux treats the USB adapter as a regular NIC (Network Interface Card), so you can assign a static IP address or use DHCP. You can configure this adapter like any other NIC. USB Port Compatibility Even though the box touts “USB 3.0,” you can plug this into any USB port, and it will work. However, you will be limited to whatever speed of the USB port you use.
![]()
Plugable adapter connected to Cat6 cable. For example, USB 3.0 and USB 3.1 both allow the adapter to operate at the full gigabit Ethernet speed. I saw not difference in performance from a motherboard Ethernet port or a dedicated Ethernet NIC. File transfers were as fast as gigabit Ethernet would allow. However, a USB 2.0 port was much, much slower when connected to the same gigabit LAN. Not because the adapter was faulty, but because USB 2.0 is limited to 480 Mbps max. Speed Tests So, does this operate at full gigabit speeds?
Yes IF plugged into either a USB 3.0 or USB 3.1 port. USB 2.0 is slower.
I performed synthetic 16GB data transfers with netcat between two computers connected to the same gigabit LAN. On the listening computer: nc -l 11111 /dev/null On the sending computer: dd if=/dev/zero bs= count=16 nc -v 192.168.1 192.168.10.10 is the static IPv4 address assigned to the USB 3 adapter.
I also unplugged all other network cables and manually specified a route using the USB adapter. Sudo route add -net 192.168.10.0 netmask 255.255.255.0 dev eth3 This tells Linux to use the adapter when talking to the 192.168.10.0 network, which is the LAN for this test.
The sending system recognized the adapter as eth3. (The predictable network naming system was disabled.) I monitored the transfer with, and the network activity in System Monitor. Comparison of the highest sustained transfer speeds observed. The results were the same sending and receiving between two computers. No other network traffic. USB 2.0/3.0/3.1 used the same system. USB 3.0 and USB 3.1 tie at 115.4 MiB/s since this is the limit of gigabit Ethernet under ideal conditions.
When plugged into a USB 2.0 port, the maximum transfer rate dropped to 43.1 MiB/s. This is normal due to the limitations of USB 2.0. (Remember to restart bmon and iftop and set the route again when unplugging and re-plugging the adapter into different USB ports.) The netbook was interesting.
The Acer Aspire 722 has a built-in 10/100Mbps Ethernet port, and this is a case of where an external USB network adapter would be useful. Plugable adapter connected to the USB 2.0 on the Acer Aspire 722 One netbook.
This provides a much faster network connection than the netbook’s builtin 10/100 Ethernet port. When connecting the netbook to a LAN using an Ethernet port, speeds top out at a constant 11.7 MiB/s. But when the USB 3.0 adapter is plugged into the netbook’s USB 2.0 port, then the transfer rate is increased to over triple the speed at 37.3 MiB/s. However, the netbook’s USB 2.0 rate is still a little lower than a full system’s USB 2.0 rate. 7G File Transfer How about transferring a real file? I formed a 7GB ZIP file of random data, and used time in Bash to measure how long it would take to transfer over the network using the FTP protocol. I installed ftp-upload for this.
Sudo apt-get install ftp-upload ftp-upload is a program designed to script file transfers. Time ftp-upload -h 192.168.10.10 -u username -p password -d data.zip data.zip is the 7GB data file, and 192.168.10.10 is the destination computer to transfer the file to. This test was performed with each USB port to check for differences. An SSD to SSD file transfer was performed to eliminate any hard drive bottlenecks. How many seconds to transfer a 7GB file over the gigabit LAN using the Plugable USB 3.0 adapter?
FTP transfer results. USB 3.0 and USB 3.1 pretty much tie again due to the limitations of gigabit Ethernet. Both took a little over one minute to transfer 7GB while the USB 2.0 port took almost three minutes at 2m48.2s. Conclusion We have another product that lives up to its box claims!
With a USB 3.0/3.1 port, the Plugable USB Ethernet Adapter will transfer files as fast as a plugin NIC, and it plays seamlessly with Linux. A device like this is especially useful with a netbook or for any situation requiring a quick but speedy network connection without opening up a computer.
. To use a static IP address to connect your printer to a wired LAN connection, install the printer drivers and Printer Setting Tool, and then specify the wired LAN connection settings. You cannot use the wireless and wired function at the same time. Before you use the wired function, turn off the wireless function. Use the following procedure to print via wired LAN (Ethernet):. Download the printer driver and P-touch Editor from the section of this website.
Start the printer driver installer. Select Ethernet for the connection type, and then follow the installer instructions to complete the installation. Before connecting the LAN cable, make sure that the printer is turned Off.
Connect the LAN cable to the LAN Port on the back of the printer. Connect the LAN cable to an active LAN Port on the network. Turn the printer On.
Install and start P-touch Editor to create and print labels.
Comments are closed.
|
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |